Hi
I have 2 controllers, 1 works with access to the <CTRL> <BRK> interface since the other one stopped after an attempt to update the firmware by my client (I think he tried to update).
When connecting the serial cable, the first controller starts normally, but the second one stops at the next point below.
Even giving: <CTRL> <BRK> and then S, nothing counts. (But I think that this command would not solve the problem, because I saw the good controller, that max it does and set ip interface and change password)
Is there any special command, or some way to upload a firmware to it via TFTP or something?
If you can help me with this problem, I'm really in need of it.
Log, from the controller terminal with problems:
-=<###>=-
Instantiating /ram as rawFs, device = 0x1
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x1
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
0 FAT copies, 0 clusters, 0 sectors per FAT
Sectors reserved 0, hidden 0, FAT sectors 0
Root dir entries 0, sysId (null) , serial number 10000
Label:" " ...
Disk with 1024 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 1010 clusters, 3 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 6
Root dir entries 112, sysId VXDOS12 , serial number 10000
Label:" " ...
Instantiating /ram as rawFs, device = 0x1
OK.
RTC Error: Real-time clock device is not working
Adding 13888 symbols for standalone.
Length: 0x13c Bytes
Version ver03.0A
Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
01 Data lines Passed
02 Address lines Passed
3300 NVSRAM
01 Data lines Passed
4410 Ethernet 82574 1
01 Register read Passed
02 Register address lines Passed
6D40 Bobcat
02 Flash Test Passed
3700 PLB SRAM
01 Data lines Passed
02 Address lines Passed
7000 SE iSCSI BE2 1
01 Register Read Test Passed
02 Register Address Lines Test Passed
03 Register Data Lines Test Passed
3900 Real-Time Clock
01 RT Clock Tick Passed
Diagnostic Manager exited normally.
Current date: 12/01/17 time: 02:42:35
Send <BREAK> for Service Interface or baud rate change
12/01/17-10:46:59 (tRAID): NOTE: Set Powerup State
12/01/17-10:46:59 (tRAID): SOD Sequence is Normal, 0 on controller A
12/01/17-10:47:00 (tRAID): NOTE: Turning on tray summary fault LED
12/01/17-10:47:00 (tRAID): WARN: Error threshold exceeded: "Client_Corrupt_DB_D etected_On_Alt"
12/01/17-10:47:00 (tRAID): NOTE: Installed Protocols: <MTPs: INIC SAS USB > <IT Ps: RDMA ISER IPOIB > <STPs: FCP RmtDMA iSCSI SAS >
12/01/17-10:47:00 (tRAID): NOTE: Required Protocols: <MTPs: INIC SAS > <ITPs: UNK > <STPs: iSCSI SAS >
12/01/17-10:47:00 (tRAID): NOTE: loading flash file: iSCSI
12/01/17-10:47:02 (tRAID): NOTE: DSM: Current revision 7
12/01/17-10:47:02 (tRAID): NOTE: SYMBOL: SYMbolAPI registered.
12/01/17-10:47:03 (tRAID): NOTE: RCBBitmapManager total RPA size = 1778384896
12/01/17-10:47:03 (tRAID): NOTE: In iscsiIOQLIscsiInitDq. iscsiIoFstrBase = 0x 1
12/01/17-10:47:03 (tRAID): NOTE: loading flash file: MTLSEBET1G
*** Disabled FULL TRACE ***
12/01/17-10:47:04 (tRAID): WARN: MTLSE: before mtl_create_pool:IO task size: 0x 140
12/01/17-10:47:04 (tRAID): NOTE: init: ioc: 0, PLVersion: 11-075-20-00
12/01/17-10:47:04 (tRAID): WARN: MLM: Failed creating m_MelNvsramLock
12/01/17-10:47:04 (tRAID): WARN: MLM: Failed creating m_MelEventListLock
12/01/17-10:47:05 (tRAID): NOTE: CrushMemoryPoolMgr: platform and memory (CPU M emSize:2048), adjusted allocating size to 65536 for CStripes
12/01/17-10:47:06 (tRAID): SOD: Instantiation Phase Complete
12/01/17-10:47:05 (IOSched): NOTE: SAS Expander Added: expDevHandle:x11 enclHan dle:x2 numPhys:25 port:2 ioc:0 channel:0 numEntries:22
12/01/17-10:47:05 (tRAID): WARN: Error threshold exceeded: "Client_Corrupt_DB_D etected_On_Alt"
12/01/17-10:47:05 (tRAID): WARN: Client threshold Exceeded
12/01/17-10:47:05 (tRAID): WARN: sodLockdownCheck: sodSequence update: SuspLock down
12/01/17-10:47:05 (tRAID): WARN: No attempt made to open Inter-Controller Commu nication Channels 0-0
12/01/17-10:47:05 (tRAID): WARN: Error threshold exceeded: "Client_Corrupt_DB_D etected_On_Alt"
12/01/17-10:47:05 (tRAID): WARN: Client reported lockdown: "Client_Corrupt_DB_D etected_On_Alt"
12/01/17-10:47:05 (tRAID): NOTE: Flashing tray summary fault LED
12/01/17-10:47:05 (tRAID): WARN: Suspending Start-Of-Day Task
12/01/17-10:47:06 (tSasExpChk): NOTE: Local Expander Firmware Version: 00.00.80 .10
12/01/17-10:47:12 (tSasDiscCom): NOTE: SAS: Initial Discovery Complete Time: 37 seconds since last power on/reset, 10 seconds since sas instantiated
Press within 5 seconds: <S> for Service Interface, <BREAK> for baud rate *** Expired
ss